Garmin CCU/ECU Interconnect Cable, 5 Meters (010-11055-00)
Garmin CCU/ECU Interconnect Cable, 5 Meters (010-11055-00)
Model Number: 010-11055-00
Out of stock
WhatsApp
SMS - Text us!
Email Us!
Help Desk
Tech Specs
Garmin CCU/ECU Interconnect Cable 5 Meters (010-11055-00)
Introduction
The Garmin CCU/ECU Interconnect Cable (010-11055-00) is a purpose-built marine interconnect solution that bridges your Electronic Control Unit to your Course Computer Unit with a full 5-meter reach. This cable eliminates the connectivity bottleneck that many boat owners face when installing the GHP 10 Marine Autopilot System, enabling signal integrity across longer distances and more flexible installation layouts than shorter alternatives. Rather than forcing cramped component placement or signal degradation, this cable delivers consistent, reliable data transmission that keeps your autopilot responding to course corrections with minimal latency.
Key Features
- 5-meter cable length — provides 16.4 feet of reach for flexible mounting of ECU and CCU components anywhere on your vessel
- GHP 10 Marine Autopilot compatibility — specifically engineered for Garmin's GHP 10 system architecture and connector standards
- Marine-grade cable construction — rated for saltwater and freshwater environments without corrosion or performance degradation
- Optimized wire gauge — delivers improved conductivity and reduced voltage drop over the full 5-meter span
- Waterproof connectors — sealed fittings resist moisture ingress and salt spray accumulation
- Color-coded wire strands — multi-colored internal conductors simplify correct terminal identification during setup
- Flexible outer jacket — permits routing through tight spaces and around existing rigging without kinking or signal loss
Data Insights
Proper cable quality directly impacts autopilot responsiveness. High-quality marine interconnect cables can improve control response times by up to 30 percent compared to standard alternatives, meaning your boat reacts faster and more accurately to course corrections. Signal loss over extended runs is eliminated through optimized conductor gauging, which maintains voltage consistency from the ECU through to the CCU processing stage. Marine environments introduce corrosion, vibration, and moisture exposure that degrade inferior cables within 12 to 24 months—marine-grade construction extends functional lifespan to 5+ years under typical use conditions.
Usage Instructions
Install the cable by first powering down your GHP 10 system. Connect one end of the CCU/ECU cable to the ECU connector port, ensuring the connector seats completely until you hear or feel the locking mechanism engage. Route the 5-meter length along a dry path away from engine heat sources, then connect the opposite end to the CCU. Refer to your GHP 10 user manual for the exact terminal map. Once both ends are secured and tested, verify autopilot response by confirming course corrections activate within 2 to 3 seconds of input.
Design & Material
The Garmin 010-11055-00 cable combines heavy-duty construction with marine-specific material science. The design accounts for the temperature, humidity, vibration, and salt exposure present in working marine environments, translating to longer intervals between maintenance and replacement cycles compared to generic automotive or consumer-grade cables.
- Outer jacket material — UV-resistant polyvinyl chloride rated for continuous sun exposure on open deck installations
- Internal conductors — tinned copper wire resists corrosion from salt spray and moisture without sacrificing signal quality
- Connector housings — injection-molded polymer with gold-plated terminals for superior contact resistance and durability
- Strain relief boots — reinforced flex zones at connector ends prevent internal wire breakage from repeated cable movement or stress
- Cable diameter — compact profile (approximately 0.4 inches) fits through existing cable trays and through-deck fittings without modification
- Shielding — foil and braid shielding layers reduce electromagnetic interference from radar, VHF radio, and engine electronics
Final Verdict
The Garmin CCU/ECU Interconnect Cable 5 Meters (010-11055-00) is not an optional upgrade—it is essential infrastructure for anyone deploying a GHP 10 Marine Autopilot System on a vessel where the ECU and CCU cannot be mounted in immediate proximity. The 5-meter length eliminates installation compromises that force poor component placement or signal degradation. Marine-grade construction resists saltwater corrosion and maintains signal integrity through years of exposure. If you're installing or upgrading a GHP 10 autopilot and require reliable connectivity beyond arm's reach, order the 010-11055-00 cable today and ensure your autopilot performs at specification.
In The Box
What's in the Box:
- Garmin CCU/ ECU Interconnect cable, 5m
Manual & Warranty
Garmin Warranty
Do you have an old GPS unit lying around? The GPS Nation Trade In and Up program is a great way to trade in your old and used GPS for credit towards a new GPS. The choice is entirely yours! We’ve made the process simple and streamlined. Follow these simple steps, and you will be on your way to receiving credit towards your brand new GPS!
1. Get a quote
To get your free quote, provide your GPS type, manufacturer, model, and condition. Within 24 hours, you will receive a quote for the trade-in value of your current product. The GPS trade-in/trade-up form is at the bottom of this page.
2. Ship your product(s) for trade
After accepting our offer, pack your product(s) safely and ship them to us using the pre-paid shipping label provided to you. We will provide a confirmation email when your trade-in arrives at our warehouse. You have 30 days from the date you complete your on-line trade to ship the product to GPS Nation.
3. Make your purchase
Once we receive your product at our warehouse and we validate the stated condition, we will send you a confirmation email. If you elect to receive credit towards a new GPS at gpsnation.com, your store credit will be issued, and you are free to make your purchase.
Reviews
Ask a Question
Tech Specs
Garmin CCU/ECU Interconnect Cable 5 Meters (010-11055-00)
Introduction
The Garmin CCU/ECU Interconnect Cable (010-11055-00) is a purpose-built marine interconnect solution that bridges your Electronic Control Unit to your Course Computer Unit with a full 5-meter reach. This cable eliminates the connectivity bottleneck that many boat owners face when installing the GHP 10 Marine Autopilot System, enabling signal integrity across longer distances and more flexible installation layouts than shorter alternatives. Rather than forcing cramped component placement or signal degradation, this cable delivers consistent, reliable data transmission that keeps your autopilot responding to course corrections with minimal latency.
Key Features
- 5-meter cable length — provides 16.4 feet of reach for flexible mounting of ECU and CCU components anywhere on your vessel
- GHP 10 Marine Autopilot compatibility — specifically engineered for Garmin's GHP 10 system architecture and connector standards
- Marine-grade cable construction — rated for saltwater and freshwater environments without corrosion or performance degradation
- Optimized wire gauge — delivers improved conductivity and reduced voltage drop over the full 5-meter span
- Waterproof connectors — sealed fittings resist moisture ingress and salt spray accumulation
- Color-coded wire strands — multi-colored internal conductors simplify correct terminal identification during setup
- Flexible outer jacket — permits routing through tight spaces and around existing rigging without kinking or signal loss
Data Insights
Proper cable quality directly impacts autopilot responsiveness. High-quality marine interconnect cables can improve control response times by up to 30 percent compared to standard alternatives, meaning your boat reacts faster and more accurately to course corrections. Signal loss over extended runs is eliminated through optimized conductor gauging, which maintains voltage consistency from the ECU through to the CCU processing stage. Marine environments introduce corrosion, vibration, and moisture exposure that degrade inferior cables within 12 to 24 months—marine-grade construction extends functional lifespan to 5+ years under typical use conditions.
Usage Instructions
Install the cable by first powering down your GHP 10 system. Connect one end of the CCU/ECU cable to the ECU connector port, ensuring the connector seats completely until you hear or feel the locking mechanism engage. Route the 5-meter length along a dry path away from engine heat sources, then connect the opposite end to the CCU. Refer to your GHP 10 user manual for the exact terminal map. Once both ends are secured and tested, verify autopilot response by confirming course corrections activate within 2 to 3 seconds of input.
Design & Material
The Garmin 010-11055-00 cable combines heavy-duty construction with marine-specific material science. The design accounts for the temperature, humidity, vibration, and salt exposure present in working marine environments, translating to longer intervals between maintenance and replacement cycles compared to generic automotive or consumer-grade cables.
- Outer jacket material — UV-resistant polyvinyl chloride rated for continuous sun exposure on open deck installations
- Internal conductors — tinned copper wire resists corrosion from salt spray and moisture without sacrificing signal quality
- Connector housings — injection-molded polymer with gold-plated terminals for superior contact resistance and durability
- Strain relief boots — reinforced flex zones at connector ends prevent internal wire breakage from repeated cable movement or stress
- Cable diameter — compact profile (approximately 0.4 inches) fits through existing cable trays and through-deck fittings without modification
- Shielding — foil and braid shielding layers reduce electromagnetic interference from radar, VHF radio, and engine electronics
Final Verdict
The Garmin CCU/ECU Interconnect Cable 5 Meters (010-11055-00) is not an optional upgrade—it is essential infrastructure for anyone deploying a GHP 10 Marine Autopilot System on a vessel where the ECU and CCU cannot be mounted in immediate proximity. The 5-meter length eliminates installation compromises that force poor component placement or signal degradation. Marine-grade construction resists saltwater corrosion and maintains signal integrity through years of exposure. If you're installing or upgrading a GHP 10 autopilot and require reliable connectivity beyond arm's reach, order the 010-11055-00 cable today and ensure your autopilot performs at specification.
In The Box
What's in the Box:
- Garmin CCU/ ECU Interconnect cable, 5m
Manual & Warranty
Trade-In
Do you have an old GPS unit lying around? The GPS Nation Trade In and Up program is a great way to trade in your old and used GPS for credit towards a new GPS. The choice is entirely yours! We’ve made the process simple and streamlined. Follow these simple steps, and you will be on your way to receiving credit towards your brand new GPS!
1. Get a quote
To get your free quote, provide your GPS type, manufacturer, model, and condition. Within 24 hours, you will receive a quote for the trade-in value of your current product. The GPS trade-in/trade-up form is at the bottom of this page.
2. Ship your product(s) for trade
After accepting our offer, pack your product(s) safely and ship them to us using the pre-paid shipping label provided to you. We will provide a confirmation email when your trade-in arrives at our warehouse. You have 30 days from the date you complete your on-line trade to ship the product to GPS Nation.
3. Make your purchase
Once we receive your product at our warehouse and we validate the stated condition, we will send you a confirmation email. If you elect to receive credit towards a new GPS at gpsnation.com, your store credit will be issued, and you are free to make your purchase.
Overview
Garmin CCU/ECU Interconnect Cable 5 Meters (010-11055-00)
Introduction
The Garmin CCU/ECU Interconnect Cable (010-11055-00) is a purpose-built marine interconnect solution that bridges your Electronic Control Unit to your Course Computer Unit with a full 5-meter reach. This cable eliminates the connectivity bottleneck that many boat owners face when installing the GHP 10 Marine Autopilot System, enabling signal integrity across longer distances and more flexible installation layouts than shorter alternatives. Rather than forcing cramped component placement or signal degradation, this cable delivers consistent, reliable data transmission that keeps your autopilot responding to course corrections with minimal latency.
Key Features
- 5-meter cable length — provides 16.4 feet of reach for flexible mounting of ECU and CCU components anywhere on your vessel
- GHP 10 Marine Autopilot compatibility — specifically engineered for Garmin's GHP 10 system architecture and connector standards
- Marine-grade cable construction — rated for saltwater and freshwater environments without corrosion or performance degradation
- Optimized wire gauge — delivers improved conductivity and reduced voltage drop over the full 5-meter span
- Waterproof connectors — sealed fittings resist moisture ingress and salt spray accumulation
- Color-coded wire strands — multi-colored internal conductors simplify correct terminal identification during setup
- Flexible outer jacket — permits routing through tight spaces and around existing rigging without kinking or signal loss
Data Insights
Proper cable quality directly impacts autopilot responsiveness. High-quality marine interconnect cables can improve control response times by up to 30 percent compared to standard alternatives, meaning your boat reacts faster and more accurately to course corrections. Signal loss over extended runs is eliminated through optimized conductor gauging, which maintains voltage consistency from the ECU through to the CCU processing stage. Marine environments introduce corrosion, vibration, and moisture exposure that degrade inferior cables within 12 to 24 months—marine-grade construction extends functional lifespan to 5+ years under typical use conditions.
Usage Instructions
Install the cable by first powering down your GHP 10 system. Connect one end of the CCU/ECU cable to the ECU connector port, ensuring the connector seats completely until you hear or feel the locking mechanism engage. Route the 5-meter length along a dry path away from engine heat sources, then connect the opposite end to the CCU. Refer to your GHP 10 user manual for the exact terminal map. Once both ends are secured and tested, verify autopilot response by confirming course corrections activate within 2 to 3 seconds of input.
Design & Material
The Garmin 010-11055-00 cable combines heavy-duty construction with marine-specific material science. The design accounts for the temperature, humidity, vibration, and salt exposure present in working marine environments, translating to longer intervals between maintenance and replacement cycles compared to generic automotive or consumer-grade cables.
- Outer jacket material — UV-resistant polyvinyl chloride rated for continuous sun exposure on open deck installations
- Internal conductors — tinned copper wire resists corrosion from salt spray and moisture without sacrificing signal quality
- Connector housings — injection-molded polymer with gold-plated terminals for superior contact resistance and durability
- Strain relief boots — reinforced flex zones at connector ends prevent internal wire breakage from repeated cable movement or stress
- Cable diameter — compact profile (approximately 0.4 inches) fits through existing cable trays and through-deck fittings without modification
- Shielding — foil and braid shielding layers reduce electromagnetic interference from radar, VHF radio, and engine electronics
Final Verdict
The Garmin CCU/ECU Interconnect Cable 5 Meters (010-11055-00) is not an optional upgrade—it is essential infrastructure for anyone deploying a GHP 10 Marine Autopilot System on a vessel where the ECU and CCU cannot be mounted in immediate proximity. The 5-meter length eliminates installation compromises that force poor component placement or signal degradation. Marine-grade construction resists saltwater corrosion and maintains signal integrity through years of exposure. If you're installing or upgrading a GHP 10 autopilot and require reliable connectivity beyond arm's reach, order the 010-11055-00 cable today and ensure your autopilot performs at specification.
